Painting and Decorating Made Easier!

Just to clarify things: Easy and fast is not necessarily the most recommended way to paint something. However, for everyone, we sometimes want things to go a little easier or to happen a little quicker.

 

Painting is no different. By taking some precautions, we can guarantee some degree of quality, no matter how fast or easy the work is. Having the right amount of skill is usually the ticket.

 

There are any number of items that can be painted the easy way, and as fast as you might want to complete them. Example: Using an airless spray system, I once prime finished just under 3000 linear feet of molding in less than an hour. When calculated using a brush and/or roller, it would have taken the entire day. Yes, a high level of productivity can be achieved daily, depending on the situation.

 

A FEW PREP-LEVEL TIPS

 

  1. Make an assessment of the project.
  2. Determine the steps needed to complete the project. The general rule is: The fewer steps there are, the easier it will be to complete. And, you will be finished in no time.
  3. Next, evaluate how difficult it will be to complete each step. Example: To paint a louvered door, you must (a) sand each piece of wood or metal as the case may be, (b) dust the surface, and (c) apply the paint using your chosen method. Here, the process of sanding can slow the paint process down quite a bit. It would be no big deal, if all you had to do was paint it.

 

So, how can you make a job easy, or develop a faster way of doing it? Let’s take the easy part of it first. You might want to follow the steps below.

 

  1. Answer this question: What is the largest size brush to use for painting this surface? A 1-inch brush is used for detail and glass framework. A 4-inch brush is used for flat, open wall areas and wide trim such as crown molding. Determine which one’s best suited for you and the job.

 

  1. When selecting a roller system: Relate the viscosity of the paint to the type of surface. Applying paint with a roller is easiest if the paint spreads smoothly, and you don’t have to dip the roller every five seconds. Example: Use a 3/8 inch roller cover when painting brick or concrete block. And, you will fight it the entire time.

 

  1. What can be easier than using a spray gun? Assess the surface and which spray tip is the most appropriate to apply the paint evenly. For those of you familiar with tip sizes, a 3-11 is best suited for trim painting and multiple small objects. It is possible to work yourself to death painting large wall spaces with a small tip. Recommendation: A 4-17 or 5-21 are the optimum choices here.

 

 Now: How can you paint this faster than, say, the last time? Think: Spray it!

 

A well-seasoned painter, with comprehensive knowledge in spray painting, will know intuitively how to get the most out of his spray work. Here are several things that he or she might bring to the attention of a less experienced painter.

 

  1. Completely strain the paint prior to siphoning or pressurizing. This step cannot be stressed enough.
  2. Make sure that all system filters are clean. Replace at regular intervals.
  3. Make sure the spray tip is not worn, and does not leak as you trigger the gun.
  4. Assess hourly use of each spray tip per manufacturer recommendations with type of paint.
  5. Thin paint or coating material to the proper viscosity NOTE: This will increase ease of paint flow and pumping efficiency.
  6. At all times, maintain a posture and spray gun motion which is perpendicular to the surface. 7. Cover everything within close proximity to the work that does not get painted. Use plastic sheeting, paper and drop cloths.
  7. Use a mask as necessary – one appropriate for the product, space, exposure, ventilation, etc.

 

How to Optimize Ease and Speed in Unison

 

Normally, I would consider it difficult to work fast and for the work to be easy at the same time. It takes some concentration to achieve what you’re looking for. There a few things you can do.

 

  1. Spray finish as much as possible before having to bring out the roller and brush. Your productivity will be considerably higher; and the hand tool use won’t have worn you out.

 

  1. Use a roller system in place of where you typically would have used a brush.

 

  1. Upgrade or vary the brush size from what you would normally use.

 

  1. Provide the highest level of surface preparation available.

 

To make a paint job easier, it is not necessary to cut corners or costs. Ease comes with experience: knowing how to complete a task using a sound and simple method versus getting too involved.

 

Start simple and build from there. Example: Don’t try to strip wood without using a chemical remover.

 

Fast means: You will be done sooner and generally make more money. Just don’t sacrifice quality and end up back where you started: behind schedule.

 

************************************

I hope that you enjoyed your Thanksgiving holiday. Thanks for visiting “Painting with Bob,”

Copyright 2016. Robert D. Hajtovik. All rights reserved.

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Tag Cloud

%d bloggers like this: